Temperature Transducer with surface sensor, with silicone cable and magnetic clamp, with display, with changeover contact, Modbus RTU

SKU: FS1052

Category: Temperature Transducer

-40...+250°C
Modbus RTU, relay
DIP-switch-technology
optional with LCD-Display
protection type IP65
magnetic adhesive force 90 N
hinge lock technology

Output: Modbus RTU
Equipment: without

Display

Display, Relay

Relay
Cable: 2 m silicone (2x0,22 mm²)
Temperature: -40...+250°C

from 238,75 €

incl. 19% VAT , plus

This item has variations. Please select the requested variation.

The magnetic FS1052 surface transducer registers the temperature on metal surfaces and converts this measured value into a digital output signal. Using the especially powerful 90 N holding magnet it is attached directly to the surface and thus ensures a clear measurement signal, even during strong vibrations. As special equipment a potential-free alternating contact and/or a backlit display are available The contents of the display can be rotated in steps of 90° by using a command. As special functions a series of defined measured values from other bus-participants (also cross-manufacturers) can be shown in the display. To display measured values from other bus-participants these are entered into the corresponding register by the bus-Master. The optional alternating contact can be configurated for measured values from other bus-participants. The configuration of address, transmission mode/speed, terminating resistor and master/slave function of the bus-devices can easily be done using the innovative DIP switch technology. Thus devices can quickly and easily integrated into the system and later parameterised via the master. The bus-devices can even be reset to the works settings during operation of the master. Thus the basic functionality of the device is recreated in a matter of seconds. This can be necessary in the event of incorrect parameterisations of, e.g. offset, switching threshold, display modes etc.. By means of the FS master/slave topology autarkic nodes without additional SPS master can be installed within the device series. Hereby a bus-device assumes the master function in the node. This requests the measured values from other bus-participants, automatically enters these into the corresponding register and shows them in the internal display. Furthermore the master can evaluate and operate additional actuators in the device series (analogue in- and outputs, relay station).

Manufacturer information:

FuehlerSysteme eNET International GmbH
Röthensteig 11
90408 Nürnberg

+49 911 37322-0
info@fuehlersysteme.de

Measurement range temp.:	-40...+250°C
Accuracy:	±0,2 K + max. ±1% mv (-30?+100°C), else ±0,3 K + max. ±1,5% mv
Supply voltage:	24 V DC (±5%)
Current consumption:	max. 20 mA + 30 mA (option display) + 20 mA (option relay)
Alarm output:	1 x potential-free change-over contact, 48 V, 1 A
Digital output:	Modbus RTU
Switching Hysteresis Relay:	can be entered in the register
Offset:	can be entered in the register
Electrical connection:	push-in terminal, no tools required, time-saving
Display:	optional LCD display with backlight on/off/auto
Cable:	2 m silicone cable (max. +180°C)
Cable gland:	PG11 high-strength cable gland with strain relief
Housing:	Polycarbonate PC UL 94 V0 with hinge locks, color signal white similar to RAL 9003
Dimensions:	Housing: L 89 x W 80 x H 47 mm, Magnet: L 40 x W 25 x H 25 mm
Protection type:	IP65 (housing), IP54 (probe)
Protection class:	III
Working range r.H.:	0...98% r.H. in contaminant-free, non-condensing air
Working temperature:	Probe: -40...+400°C, Electronic: -20...+70°C
Storage temperature:	-20...+70°C
Installation:	remove metal plate of the magnet and put on chosen measuring point straight tighten on
Approvals:	CE, EAC, RoHS