Temperature Transducer with surface sensor, with PVC line and self-adhesive mounting cap, with display, with changeover contact, Modbus RTU

SKU: FS1050

Category: Temperature Transducer

-20...+105°C
Modbus RTU, relay
DIP-switch-technology
optional with LCD-Display
protection type IP65
aluminium contacting block
incl. self-adhesive mounting cap
hinge lock technology

Output: Modbus RTU
Equipment: without

Display

Display, Relay

Relay
Cable: 2 m PVC (2x0,14 mm²)
Temperature: -20...+105°C

from 181,95 €

incl. 19% VAT , plus

This item has variations. Please select the requested variation.

The self-adhering FS1050 surface transducer registers the temperature on surfaces and converts this measured value into a digital output signal. Using the self-adhering mounting cap, included in the scope of delivery, the temperature sensor is quickly and securely mounted, e.g. on window fronts. As special equipment a potential-free alternating contact and/or a backlit display are available The contents of the display can be rotated in steps of 90° by using a command. As special functions a series of defined measured values from other bus-participants (also cross-manufacturers) can be shown in the display. To display measured values from other bus-participants these are entered into the corresponding register by the bus-Master. The optional alternating contact can be configurated for measured values from other bus-participants. The configuration of address, transmission mode/speed, terminating resistor and master/slave function of the bus-devices can easily be done using the innovative DIP switch technology. Thus devices can quickly and easily integrated into the system and later parameterised via the master. The bus-devices can even be reset to the works settings during operation of the master. Thus the basic functionality of the device is recreated in a matter of seconds. This can be necessary in the event of incorrect parameterisations of, e.g. offset, switching threshold, display modes etc.. By means of the FS master/slave topology autarkic nodes without additional SPS master can be installed within the device series. Hereby a bus-device assumes the master function in the node. This requests the measured values from other bus-participants, automatically enters these into the corresponding register and shows them in the internal display. Furthermore the master can evaluate and operate additional actuators in the device series (analogue in- and outputs, relay station).

Manufacturer information:

FuehlerSysteme eNET International GmbH
Röthensteig 11
90408 Nürnberg

+49 911 37322-0
info@fuehlersysteme.de

Measurement range temp.:	-20...+105°C
Accuracy:	±0,2 K + max. ±1% mv (-30?+100°C), else ±0,3 K + max. ±1,5% mv
Supply voltage:	24 V DC (±5%)
Current consumption:	max. 20 mA + 30 mA (option display) + 20 mA (option relay)
Alarm output:	1 x potential-free change-over contact, 48 V, 1 A
Digital output:	Modbus RTU
Switching Hysteresis Relay:	can be entered in the register
Offset:	can be entered in the register
Electrical connection:	push-in terminal, no tools required, time-saving
Display:	optional LCD display with backlight on/off/auto
Cable:	2 m PVC cable (max. +105°C)
Material:	Contacting block: aluminium
Cable gland:	PG11 high-strength cable gland with strain relief
Housing:	Polycarbonate PC UL 94 V0 with hinge locks, color signal white similar to RAL 9003
Dimensions:	Housing: L 89 x W 80 x H 47 mm, Contacting block: L 30 x W 6 x H 6 mm, bore hole Ø 3 mm
Protection type:	IP65
Protection class:	III
Working range r.H.:	0...98% r.H. in contaminant-free, non-condensing air
Working temperature:	Probe: -20...+105°C, Electronic: -20...+70°C
Storage temperature:	-20...+70°C
Installation:	self-adhesive fixing cap (in scope of delivery), screw fastening
Approvals:	CE, EAC, RoHS