Temperature Transducer with surface sensor, with silicone cable and contact sensor with tension band, with display, with changeover contact, Modbus RTU

SKU: FS1053

Category: Temperature Transducer

-50...+180°C
Modbus RTU, relay
DIP-switch-technology
optional with LCD-Display
protection type IP65
hinge lock technology

Output: Modbus RTU
Equipment: without

Display

Display, Relay

Relay
Cable: 2 m silicone (2x0,22 mm²)
Temperature: -50...+180°C

from 181,95 €

incl. 19% VAT , plus

This item has variations. Please select the requested variation.

The FS1053 temperature transducer with silicon cable registers the surface temperature on pipelines and converts this measured value into a digital output signal. Using the strap, which is included in the scope of delivery, the application block of the temperature transducer can be quickly and securely directly fastened to, for example, the cold or hot water pipes of heating systems. As special equipment a potential-free alternating contact and/or a backlit display are available The contents of the display can be rotated in steps of 90° by using a command. As special functions a series of defined measured values from other bus-participants (also cross-manufacturers) can be shown in the display. To display measured values from other bus-participants these are entered into the corresponding register by the bus-Master. The optional alternating contact can be configurated for measured values from other bus-participants. The configuration of address, transmission mode/speed, terminating resistor and master/slave function of the bus-devices can easily be done using the innovative DIP switch technology. Thus devices can quickly and easily integrated into the system and later parameterised via the master. The bus-devices can even be reset to the works settings during operation of the master. Thus the basic functionality of the device is recreated in a matter of seconds. This can be necessary in the event of incorrect parameterisations of, e.g. offset, switching threshold, display modes etc.. By means of the FS master/slave topology autarkic nodes without additional SPS master can be installed within the device series. Hereby a bus-device assumes the master function in the node. This requests the measured values from other bus-participants, automatically enters these into the corresponding register and shows them in the internal display. Furthermore the master can evaluate and operate additional actuators in the device series (analogue in- and outputs, relay station).

Manufacturer information:

FuehlerSysteme eNET International GmbH
Röthensteig 11
90408 Nürnberg

+49 911 37322-0
info@fuehlersysteme.de

Measurement range temp.:	-50...+180°C
Accuracy:	±0,2 K + max. ±1% mv (-30?+100°C), else ±0,3 K + max. ±1,5% mv
Supply voltage:	24 V DC (±5%)
Current consumption:	max. 20 mA + 30 mA (option display) + 20 mA (option relay)
Alarm output:	1 x potential-free change-over contact, 48 V, 1 A
Digital output:	Modbus RTU
Switching Hysteresis Relay:	can be entered in the register
Offset:	can be entered in the register
Electrical connection:	push-in terminal, no tools required, time-saving
Display:	optional LCD display with backlight on/off/auto
Cable:	2 m silicone cable (max. +180°C)
Material:	Contacting block: aluminium
Cable gland:	PG11 high-strength cable gland with strain relief
Housing:	Polycarbonate PC UL 94 V0 with hinge locks, color signal white similar to RAL 9003
Dimensions:	Housing: L 89 x W 80 x H 47 mm
Protection type:	IP65
Protection class:	III
Working range r.H.:	0...98% r.H. in contaminant-free, non-condensing air
Working temperature:	Probe: -50...+180°C, Electronic: -20...+70°C
Storage temperature:	-20...+70°C
Installation:	clamping band, band width 9 mm, chucking capacity 50-110 mm, galvanized steel (in scope of delivery)
Approvals:	CE, EAC, RoHS