Air Quality Transducer for CO2, mixed gas VOC in room housing, with display, with changeover contact, 0-10 V

SKU: CO2VOC-R/A

Category: Air Quality

Manufacturer: FuehlerSysteme

0-2000/5000/10000 ppm
mixed gas VOC
0-10 V, changer
optional LCD-Display

Output: 2 x 0-10 V, changer
CO2: 0-2000/5000/10000 ppm
Version: with display

without display
VOC: 0-100%

Low stock level

from 484,68 €

incl. 19% VAT , plus

This item has variations. Please select the requested variation.

low", "medium" and "high".

Manufacturer information:

FuehlerSysteme eNET International GmbH
Röthensteig 11
90408 Nürnberg

+49 911 37322-0
info@fuehlersysteme.de

Measurement range CO2:	0-10000 ppm, scales: 0-2000/5000/10000 ppm
Measurement range VOC:	0-100% (good / bad air quality, referring to the calibration gas)
Scales:	0-2000/5000/10000 ppm
Accuracy:	CO2: 0-2000 ppm: ±50 ppm + 2% f. mv, 0-5000 ppm: ±50 ppm + 3% f. mv, else: ±100 ppm + 5% f. mv; VOC: ±15% FS (20°C, 1013 mbar, auto-calibration ON)
Temperature dependency:	CO2: ±5 ppm / K
Long term stability:	±1% FS/year
Sensor:	CO2: nondispersive infrared sensor (NDIR); VOC: metal oxide sensor
Response time (t90):	< 5 min
Sensor protection:	mounted inside housing
Supply voltage analog 0-10 V:	24 V AC/DC (±5%)
Current consumption:	Ø 100 mA
Analogue output 0-10 V:	3-wire connection
Alarm output:	1 x potential-free change-over contact, 48 V, 1 A
Switching Hysteresis Relay:	2% FS (without Display), 0,5...5% FS adjustable (with Display)
Electrical connection:	screw terminals max. 1,5 mm²
Display:	optional LCD display with backlight on/off/auto
Automatic calibration:	The automatic CO2/VOC calibration takes place every 7 days, this compensates for any drifts and achieves excellent long-term stability. To ensure this function, the device must be supplied with power for at least 7 days without interruption and ventilated once with fresh air (CO2 300...400 ppm) for approx. 10 minutes within this period. For the CO2 calibration, the device saves the minimum CO2 value measured during this period internally. After 7 days, this minimum value is normalized to 400 ppm CO2 and the output signal corrected accordingly. The maximum correction is limited to half of the determined drift. If the measured value falls below approx. 300 ppm, the calibration is initialized to 400 ppm. The automatic calibration can be deactivated and performed manually if necessary.
Pressure dependency:	CO2: 0,16% f. mv/hPa
Running-in time:	10 min
Initial operation:	After switch-on of the device follows a self-test and the tempering, which takes ca. 10 minutes depending on the environmental conditions. At this time the analogue output drifts from the actual measurement value.
Cable gland:	on the back or housing side (predetermined breaking point)
Housing:	ABS polyman, colour signal white like RAL 9003
Dimensions:	Housing: L 82 x W 82 x H 25 mm
Protection type:	IP30, IP20 (with display)
Protection class:	III
Working range r.H.:	0...98% r.H. in contaminant-free, non-condensing air
Working temperature:	0...+50°C
Manual calibration:	The manual CO2 calibration of the output signal to 400 ppm (zero point) is started by pressing the button on the circuit board (hold it down for approx. 5 seconds until the LED flashes). Before that, continuous operation of min. 10 minutes in fresh air. The LED is deactivated after successful calibration. The manual VOC calibration of the output signal to 1V (zero point) is started by pressing the button on the circuit board (hold down for approx. 5 seconds until the LED flashes). Before that, continuous operation of min. 2 hours with air defined as normal air quality. The LED is deactivated after successful calibration.
Storage temperature:	-20...+50°C
Installation:	on-wall or on flush-mounted box
Approvals:	CE, EAC, RoHS